Cut down the template according to your demand, Stick the template on the door and frame
According to the position of the installation template, drill holes to install the screws.
Take off Main Arm and Adjective Arm. Put the arm and the door closer main body in cross shape. Install the arm on the square tenon of gearing bearing. Then fasten by the assembled screw.
According to the drilled holes, install the door closer body on frame or door.
Pre load the arm to an angle and then install it together with the Adjective Arm which is vertical to the door. Adjust the length of the Arm to install the Arm. At last, fasten the screws on the arm.
Put dust proof cap on the other end of the gear shaft
The standard installation
The template of the right hand pull side door vertical installation. (The template of the left hand pull side door vertical installation is opposite of the template of the right hand pull side door vertical installation).
The reverse installation
The template of the left hand push side door vertical installation. (The template of the right hand push side door vertical installation is opposite of the template of the left hand push side door vertical installation).
The steps of parallel installation
According to the mark, fold the parallel installation template to 900. Stick it on the door and frame
According to the position of the installation template, drill screw holes.
According to the drilled holes, install the door closer main body and PA board on the door and door frame. Then fasten.
Take off the bracket of the Adjective Arm, Preload the arm to 450, Install the arm on the square tenon of gearing bearing. Then fasten by the assembled screw.
Adjust the length of the Adjective Arm to install the Arm, make it parallel with door closer main body. Put the clamp cover on the gear of the parallel board. Fasten the assembled screw, Then fasten the nut of the link.
Put the dust-proof cap on the other end of the gear shaft.
Adjust the speed of the door closer by:-
The Closing speed regulation valve and latching speed regulation valve.
Counter-clockwise turning can make the speed faster. On the contrary, clockwise turning will make the speed slower.
The parallel installation
The template of the right hand push side door parallel installation (The template of the left hand push side door parallel installation is opposite of the template of the right and push side door parallel installation)
Notices.
Please don't rotate the direction of the square tenon of the gear before install the door closer.
Please don't hit the square tenon of the gear hard when you install the arm.
Door closer can auto-close the door by themselves extra efforts to close the door are not permitted.
Fasten the all screws after half a moth with use.
Pay attention to the speed regulation in the summer and winter seasons.
Please don't screw the regulating valve off main body, when you adjust the speed.
*If you have any specific question related to the product, please contact us.
Fit the Fix BrackeKg)ts on bed frame as per given dimension. (Ref. Fig.1) without the gas spring fitted.Now fix the bed platform to the top brackets. (Ref. Fig.2).
*If you have any specific question related to the product, please contact us.
Fit the Fix Brackets on bed frame as per given dimension. (Ref. Fig.1) without the gas spring fitted.Now fix the bed platform to the top brackets. (Ref. Fig.2).
*If you have any specific question related to the product, please contact us.
Use Ø35mm cutter to make cavities on the inside of shutter. (Refer Fig.1).Cavity should be 10mm deep.Fit top housing and bottom housing in top and bottom cavities respectively.Rail is fitted in a slot at top and bottom of cabinet. Groove should be 8mm wide and 6mm deep. (Refer Fig.2).Wheel of bottom housing should sit in bottom rail.Spring loaded guide in top housing is pulled down so as to engage in top rail there by retaining the shutter. (Refer Fig.3).
*If you have any specific question related to the product, please contact us.
One set is for one sliding shutters.Set of two sliding fittings with four wheels, each are fitted on top rack. (Refer fig.1).Set of two sliding fittings with one wheel, each are fitted on bottom track. (Refer fig.2).Cavities for sliding fittings are made at the four extreme ends of shutter. (Refer fig.3).Center distance between two rails should be 40 mm min. (Ref. Fig.4) IMPORTANT: TO BE ORDERED WITH THE ALUMINIUM RAILS. CODE NO. SFFA1.
*If you have any specific question related to the product, please contact us.
Drill 2 holes on each internal side of wardrobe.First hole should be 24mm from the top internal face of cabinet and center distance to be 32mm apart. (Refer fig. 1).Holes should be at equal height.
*If you have any specific question related to the product, please contact us.
Drill 2 holes on each internal side of wardrobe.First hole should be 24mm from the top internal face of cabinet and center distance to be 32mm apart. (Refer fig. 1).Holes should be at equal height.
*If you have any specific question related to the product, please contact us.
Drill 2 holes on each internal side of wardrobe.First hole should be 24mm from the top internal face of cabinet and center distance to be 32mm apart. (Refer fig. 1).Holes should be at equal height.
Introducing the Ebco Hi Slide 45 - a revolutionary product designed for Flush Mounted Sliding Shutters. Equipped with a Common Top and Bottom Track, this system is perfect for Bottom Running Shutters weighing up to 45Kgs and is also compatible with System 32. Discover the seamless and effortless operation of the Ebco Hi Slide 45. Ebco Hi Slide 45 fitting is use with Aluminium Track (for top / bottom) - 2.44m and 3.66 mm. 1 sets fitting can be used for 1 cabinet door.
